CONTROL FUNCTION

You can assign mainly system parameters to each of the top panel footswitches, the expression pedal (EXP1), and the expression pedal or footswitch connected to the rear panel CTL 2, 3/EXP 2 jack.

Press the [MENU] button.
Touch <CTL/EXP>.
Touch <CONTROL FUNCTION>.
Turn the [SELECT] knob to select the item that you want to set.
Turning the knob will move the selected item vertically.
Turn the [1]–[4] knobs to edit the value of the item selected for each switch.
Press the PAGE [Ë] button to show the next page. Press the PAGE [Í] button to show the previous page.
The control functions you can configure depend on the control mode you’re using. The areas you can configure are indicated in white, and the areas you can’t configure are indicated in gray.

The footswitch and expression pedal functions must be specified for each memory; however, if you set “PREF (PREFERENCE)” to SYSTEM, all memories will use those functions in common.

MEMO

The GX-10 lets you arrange multiple pedal effects in the effect chain like FOOT VOLUME, WAH and so on. In CONTROL FUNCTION, the pedal effect placed at the beginning of the chain (or at “A CH” in DIV/MIX) is enabled.

FUNC (É, Ç, EXP1 SW, CTL1, CTL2, CTL3, CUR NUM)


Value	Explanation
OFF	No assignment.
DOWN	Switches to the previous memory number. This can’t be assigned for the CUR NUM, or with the É and Ç switches in manual mode.
UP	Switches to the next memory number. This can’t be assigned for the CUR NUM, or with the É and Ç switches in manual mode.
BANK É	Switches to the previous BANK number. This can’t be selected with the “CUR NUM” setting, when in up/down mode or in manual mode with the É and Ç switches.
BANK Ç	Switches to the next BANK number. This can’t be selected with the “CUR NUM” setting, when in up/down mode or in manual mode with the É and Ç switches.
BPM TAP	Used for tap input of the MASTER BPM.
TUNER	Switches the TUNER on and off.
MEMORY/MAN	Switches between up/down mode (or bank/number mode) and manual mode.
TUNER/MAN	Turns the tuner on/off when briefly pressed, and switches to manual mode when long-pressed.
MAN/TUNER	Switches to manual mode when briefly pressed, and turns the tuner on/off when long-pressed.
WAH	Turn the WAH on/off. This only displays when WAH is in the effect chain.
DIV CH.SEL	Switches the DIVIDER channel select.
SEND/RETURN	Switches the SEND/RETURN on and off.
LOOP CTL	Controls the looper. For details on how to use this, refer to “Looper” in the “Reference Manual” (Web).
LOOPER STOP	Stops the phrase.
LOOPER CLEAR	Clears the phrase.
MIDI START	Controls the Start/Stop of external MIDI devices (such as sequencers).

When control mode is set to BANK/NUM mode, the switches on this unit are set to fixed values, as shown below.


Switch	Function
É	Recalls memory 1 in the bank.
Ç	Recalls memory 2 in the bank.
CTL1	Recalls memory 3 in the bank.

CURRENT NUMBER is enabled only in BANK/NUM mode.

FUNC (EXP1 PEDAL, EXP 2)


Value	Explanation
OFF	No assignment.
FOOT VOL	Assigns the foot volume.
WAH	Assign the WAH. This only displays when WAH is in the effect chain.
FV/WAH	Assigns the foot volume and the WAH effect. This only displays when FV and WAH are in the effect chain.
FV+TU	Assigns the foot volume. TUNER is displayed if the pedal is returned all the way. This only displays when FV is in the effect chain.
FV+TU/WAH	Assigns the foot volume and the WAH effect. TUNER is displayed if the pedal is returned all the way when using foot volume. This only displays when FV and WAH are in the effect chain.

MODE


Value	Explanation
TOGGLE	The setting is switched OFF (minimum value) or ON (maximum value) with each operation.
MOMENT	The normal state is Off (minimum value), with the switch On (maximum value) only while the footswitch is depressed.

PREF


Value	Explanation
MEMORY	This lets you use different settings for each memory.
SYSTEM	The same settings will be shared by all memories.