ASSIGN parameter list

OFF, ON

Turns the ASSIGN 1–20 on/off.

TARGET

Ø“TARGET list”

This selects the parameter to be changed.

MIN

This sets the minimum value for the range in which the parameter can change.

The value differs depending on the parameter assigned for TARGET parameter.

MAX

This sets the maximum value for the range in which the parameter can change. The value differs depending on the parameter assigned for TARGET parameter.

SOURCE

MAN É, MAN Ç

Assigns the [É] and [Ç] switches on this unit when set to manual mode.

CUR NUM

Assigns the same number switch as the selected memory number.

• This is enabled only in BANK/NUM mode.

CTL 1

Assigns the [C1] switch on this unit.

CTL 2, CTL 3

Assigns the external footswitch connected to the CTL 2, 3/ EXP 2 jack.

EXP 1 SW

Assigns this unit’s [EXP 1] switch.

EXP 1

Assigns this unit’s expression pedal.

EXP 2

Assigns the external expression pedal connected to the CTL 2, 3/ EXP 2 jack.

INT PDL

Assigns the internal pedal.

Refer to “Virtual expression pedal system (internal pedal / wave pedal)”

WAVE PDL

Assigns the wave pedal.

INPUT

The assigned target parameter will change according to the input level.

CC# 1–31, 64–95

Assigns control change messages from an external MIDI device.

MODE

MOMENT

The normal state is Off (minimum value), with the switch On (maximum value) only while the footswitch is depressed.

TOGGLE

The setting is switched OFF (minimum value) or ON (maximum value) with each operation.

ACT LOW

0–126

You can set the controllable range for target parameters within the source’s operational range.

Target parameters are controlled within the range set with ACT LOW and ACT HIGH.

You should normally set ACT LOW to 0 and ACT HIGH to 127.

ACT HIGH

1–127

SENS

0–100

This adjusts the input sensitivity when INPUT is selected for SOURCE.

TRIGGER ^*1

MEM CHANGE

This is activated when memory is selected.

MANÉ, MANÇ

This is activated when the [É] or [Ç] switch on this unit are pressed in manual mode.

EXP1 PDL-LO

This is activated when this unit’s expression pedal is set to the minimum position.

EXP1 PDL-MID

This is activated when this unit’s expression pedal is moved through the middle position.

EXP1 PDL-HI

This is activated when this unit’s expression pedal is set to the maximum position.

EXP1 SW

This is activated when the [EXP 1] switch is operated.

CTL 1

This is activated when the [C1] switch on this unit is operated.

CUR NUM

This is activated when you operate the same number switch as the selected memory number.

• This is enabled only in BANK/NUM mode.

EXP 2

This is activated when an external expression pedal connected to the CTL 2, 3/ EXP 2 jack is operated.

CTL 2, CTL 3

This is activated when an external footswitch connected to the CTL 2, 3/ EXP 2 jack is operated.

CC#1–31, 64–95

This is activated when a control change is received.

TIME ^*1

0–100

This specifies the time over which the internal pedal will move from the toe-raised position to the toe-down position.

CURVE ^*1

LINEAR

SLOW RISE

FAST RISE

FORM ^*2

SAW

TRI

SINE

RATE ^*2

0–100,

BPM ŀ–Ō

This determines the time spend for one cycle of the assumed wave pedal.

• When set to BPM, the value of each parameter will be set according to the value of the “MASTER BPM” specified for each memory. This makes it easier to achieve effect sound settings that match the tempo of the song.
• If, due to the tempo, the time is longer than the range of allowable settings, it is then synchronized to a period either 1/2 or 1/4 of that time.

CH ^{*3 *4}

SYSTEM

Transmits a message on the MIDI channel specified by the parameter TX CHANNEL in “MIDI SETTING”.

1–16

The message is transmitted on the specified MIDI channel.

CC#

0–127

The message is transmitted using the specified controller number.

MIN

0–127

Selects the minimum value of the transmitted CC# message.

MAX

0–127

Selects the maximum value of the transmitted CC# message.

PC#

1–128

Specifies the program number that is transmitted.

MSB

OFF, 1–128

Specifies the bank select MSB that is transmitted. If this is OFF, the bank select MSB is not transmitted.

LSB

OFF, 1–128

Specifies the bank select LSB that is transmitted. If this is OFF, the bank select LSB is not transmitted.