STEP
Parameter | Controllers | Value | Explanation |
|---|---|---|---|
Step Value | [OSC 1] slider, [2] knob | -72–+72 | Sets the step value that’s selected onscreen. |
Step Curve | [1] knob | 0–36 | Sets the step waveform that’s selected onscreen. |
Step LFO Flt Depth | [OSC 3] slider | 0–100 | Sets how much the step LFO affects the cutoff frequency. |
Step LFO Pitch | [OSC 3] button | OFF, 1 OCT, 2 OCT, 3 OCT | Sets how much the step LFO affects the pitch. 1 OCT:The pitch is raised a half step for every increase of six to the Step Value. 2 OCT:The pitch is raised a half step for every increase of three to the Step Value. 3 OCT:The pitch is raised a half step for every increase of two to the Step Value. |
Step LFO Rate Note/Rate | [OSC 4] slider | 0–1023 or 1/64T, 1/64, 1/32T, 1/32, 1/16T, 1/32., 1/16, 1/8T, 1/16., 1/8, 1/4T, 1/8., 1/4, 1/2T, 1/4., 1/2, 1T, 1/2., 1, 2T, 1., 2, 4 | Sets the speed of the step LFO cycle. The step LFO cycle is set as a note length when the Step LFO Rate Sync setting is “ON”. |
Step LFO Rate Sync | [OSC 4] button | OFF, ON | Turn this ON to sync the LFO 2 cycle with the tempo. |
Step LFO Length | - | 1–16 | Sets the number of steps. |
Step LFO Key Trig | - | OFF, ON | Specifies whether the LFO 2 cycle will be synchronized to begin when the key is pressed (ON) or not (OFF). |
Step LFO Amp Depth | - | 0–100 | Sets how much the step LFO affects the volume. |
Step LFO Pan Depth | - | -63–+63 | Sets how much the step LFO affects the pan. |
Step LFO Fade | - | 0–1023 | Sets how long it takes for the step LFO to reach maximum amplitude. |
Coarse Tune | PITCH | -24–+24 | Specifies the pitch in semitone steps (maximum ±2 octaves). |
Fine Tune | SHIFT+PITCH | -50–+50 | Specifies the pitch in cents (maximum ±50 cents). |
Osc 1 Waveform | TIMBRE | OFF, SAW, SQR, TRI, SINE, RAMP, JUNO, TRI2, TRI3, SINE2, SSAW, NOISE | This sets the waveform. |
Osc 2 Waveform | SHIFT+TIMBRE | OFF, SAW, SQR, TRI, SINE, RAMP, JUNO, TRI2, TRI3, SINE2, SSAW, NOISE | This sets the waveform. |
Osc 1 Level | - | 0–127 | Sets the volume of OSC 1. |
Osc 2 Level | [OSC 2] slider | 0–127 | Sets the volume of OSC 2. |
Osc 2 Octave | [OSC 2] button | 0, -1, -2 | Specifies the octave in which OSC 2 plays. |
Pulse Width | - | 0–63 | This effect changes the duty ratio of the pulse width to alter the waveform. You can use this effect with other waveforms besides SQR (square wave). A value of zero results in a 50:50% duty ratio. |
PWM Depth | - | 0–63 | Sets how much the step LFO is applied (depth) to the PW (pulse width). |
SSaw Detune | - | 0–127 | Adjusts how much the SuperSAW is detuned. Larger values create a greater detune effect. This is enabled only when “SSAW” is selected for the waveform. |
Mono Poly | [OSC 1] button | MONO, POLY | Specifies whether the tone will play polyphonically (POLY) or monophonically (MONO). |