OSCILLATOR section

The oscillator section is used for editing the wavetable OSC.

Select the wavetable that determines the character of the sound, and set the pitch.

You can use two layers to stack and play different wavetable sounds.

MEMO

If you’re viewing this content on your smartphone, we recommend that you turn your smartphone on its side for landscape mode.


Controller (Parameter name)	Value	Explanation
[POSITION LFO] slider [POSITION LFO] switch (Position LFO Depth)	0 to +63 (when [POSITION LFO] switch is “+”) -63 to 0 (when [POSITION LFO] switch is “-”)	Sets the intensity of change of the Wavetable Position according to the LFO. This is enabled when Drawing Switch is “OFF”. The range differs according to the value of the [POSITION LFO] switch.
[POSITION RANDOM] knob (Position Random Sens)	0–63	Sets how randomly the Wavetable Position changes when a key is pressed. This is enabled when Drawing Switch is “OFF”.
[SPREAD] knob (Spread Depth)	0 (OFF), 1–20	Setting the Spread to a higher value gives a wider stereo sound. MEMO When the Spread function is set to 1 or more, the polyphony is reduced. When you turn the knob from the “OFF” position, the Spread effect is applied to the notes that sound thereafter.
[RANGE] switch (Range)	16', 8', 4', 2'	Sets the octave for the patch.
[POSITION] slider (Position)	0–127	Sets the Wavetable Position for layers 1 and 2. This is enabled when Drawing Switch is “OFF”.
[LAYER1 WAVE] knob (Wave Layer1 Number)	001–063	Selects the Wavetable No. for layer 1. This is enabled when Drawing Switch is “OFF”.
[LAYER2 WAVE] knob (Wave Layer2 Number)	001–063	Selects the Wavetable No. for layer 2. This is enabled when Drawing Switch is “OFF”.
[LAYER2 OCT] switch (Layer2 Octave Down)	-2–0	Sets the amount of octaves by which to lower layer 2. This is enabled when Drawing Switch is “OFF”. The effect is applied when the note plays again after the switch setting has been changed.
[PITCH LFO] knob (LFO Pitch Depth)	-63–+63	Sets how much the LFO is applied to the pitch.
[POSITION ENV] slider [POSITION ENV] switch (Position Env Depth)	0 to +63 (when [POSITION ENV] switch is “NORMAL”) -63 to 0 (when [POSITION ENV] switch is “INVERT”)	Sets the intensity of change of the Wavetable Position according to the OSC Envelope. This is enabled when Drawing Switch is “OFF”. The range differs according to the value of the [POSITION ENV] switch. The effect is applied if you operate the [POSITION ENV] slider after you have toggled the [POSITION ENV] switch.
[MIX ENV] knob (Layer Mix Env Depth)	-63–+63	Sets how much OSC Envelope is applied to Layer Mix. This is enabled when Drawing Switch is “OFF”.
[MIX LFO] knob (Layer Mix LFO Depth)	-63–+63	Sets how much the LFO is applied to Layer Mix. This is enabled when Drawing Switch is “OFF”.
[LAYER MIX] slider (Layer Mix)	0–127	Sets the mix balance between layers 1 and 2. This is enabled when Drawing Switch is “OFF”.
[WAVE SHAPER] knob (S-MOD Shaping Depth)	0–127	Sets how much shaping modulation is applied.
[W.S LFO] knob (S-MOD LFO Depth)	-63–+63	Sets how much the LFO is applied to Shaping Depth.
[W.S ENV] knob (S-MOD Env Depth)	-63–+63	Sets how much OSC Envelope is applied to Shaping Depth.

What is the wavetable OSC?

A wavetable is a collection of various single-cycle waveforms. Different waveforms are arranged in continuous order inside the table, and you can specify the position from which to begin playback to produce unique sounds whose waveforms change in various ways over time.

Wavetable (example)