1. Select [MENU] Ó “KIT EDIT2”.

  2. Use the cursor [à] [á] [ã] [â] buttons to select “KIT CLICK” and press the [ENTER] button.

    The KIT CLICK screen appears.

    Use the cursor [à] [á] [ã] [â] buttons to select “Click Setting”, and the [-] [+] buttons to select “KIT” or “SYSTEM”.

    The [F1]–[F3] KIT CLICK settings are enabled only when “KIT” is selected.
    When this is set to “SYSTEM”, you can change the SYSTEM CLICK setting by pressing [F6].

    You can set the tempo by pressing the [F5] (TAP) button at the desired timing (tap tempo).

Setting the tempo and time signature ([F1] TEMPO)

Use the cursor [à] [á] [ã] [â] buttons to select a parameter, and use the [-] [+] buttons or the [VALUE] knob to edit the value.

Parameter

Value

Explanation

Tempo

20.0–260.0

Specifies the tempo.

Beat

1–9

Sets the time signature (the number of beats per measure) of the click.

Accent

0–127

Sets the accent volume.

Quarter

0–127

Sets the volume of quarter notes.

Eighth

0–127

Sets the volume of eighth notes.

Sixteenth

0–127

Sets the volume of sixteenth notes.

Triplet

0–127

Sets the volume of eighth-note triplets.


Setting the volume, sound and other settings ([F2] SETUP)

Use the cursor [à] [á] buttons to select a parameter, and use the [-] [+] buttons or the [VALUE] knob to edit the value.

Parameter

Value

Explanation

Click Mode

PLAY INTERNAL CLICK, PLAY WAVE as CLICK, PLAY WAVE as CLICK-TRACK

Selects the click mode.

PLAY INTERNAL CLICK: This mode uses the built-in click sound.
PLAY WAVE as CLICK: This mode uses a preloaded wave or a wave imported by the user.

If a waveform is selected with PLAY WAVE as CLICK, the wave at the accent position does not sound. The wave only sounds at the quarter note, eighth note, sixteenth note and triplet timings.


PLAY WAVE as CLICK-TRACK: This mode uses the click track wave imported by the user.

Click Sound (PLAY INTERNAL CLICK)
Click Wave (PLAY WAVE as CLICK)
Click-Track Wave (PLAY WAVE as CLICK-TRACK)

METRONOME, BEEP, WOOD BLOCK, STICKS, CLAVES, AGOGO, TRIANGLE, TAMBOURINE, BELL, CABASA
0–20000
0–20000

Click Sound: the built-in click sound
Click Wave: a preloaded wave or a wave imported by the user
Click-Track Wave: the click track wave imported by the user

Volume

-INF–+6.0dB

Sets the click volume.

Pan

L15–CENTER–R15

Adjusts the pan (left-right balance) of the click sound.

Click Start Pad (Range)

OFF, P1–9, T1–8, F1, F2

The click starts once you strike the selected pad.
Select a desired pad or select a range of pads.
Example: if you want the click to start when either pad 1, 2 or 3 is struck, set the range as “P1–P3”.

Pad Click Trig Type

ONE-TIME, RETRIGGER, ALTERNATE

Selects how the click operates when you strike a pad that’s set as a click start pad.

ONE-TIME: The click starts once you strike the pad.
RETRIGGER: The click restarts from the first beat every time you strike the pad.
ALTERNATE: The click starts/stops with each strike of the pad.

Click-Track Loop

OFF, ON

Plays back the wave to use as a click track in a loop (only enabled when “Click Mode” is “PLAY WAVE as CLICK-TRACK”).

LED Reference

OFF, ON

Sets whether to make the TEMPO indicator blink in time with the click (ON) or not (OFF). (This is enabled when Click Mode is “PLAY INTERNAL CLICK” or “PLAY WAVE as CLICK”.)


Setting the output destination ([F3] OUTPUT)

Use the cursor [à] [á] buttons to select a parameter, and use the [-] [+] buttons or the [VALUE] knob to edit the value.

Parameter

Value

Explanation

Output

MASTER+PHONES, PHONES-ONLY

Selects the output destination for the click.

MASTER+PHONES: Outputs to the PHONES jack and MASTER OUT jack (when “Master Direct Sw” is “NORMAL”).
PHONES-ONLY: Outputs only to the PHONES jack. No sound is output from the MASTER OUT jacks.

Direct Output

OFF, DIRECT 1–4, DIRECT 1+2/3+4 (L+R), MASTER DIRECT L/R, MASTER DIRECT L+R

Selects the direct out output destination for the click.
This sets the output from the DIRECT OUT 1-4 jacks and MASTER OUT jacks (when “Master Direct Sw” is “DIRECT”).
Editing the system click settings ([F6] SYSTEM)

The [F6] (SYSTEM) button is shown when “Click Setting” is set to “SYSTEM” (when the system click is used).

  1. Use the cursor [à] [á] buttons to select a parameter, and use the [-] [+] buttons or the [VALUE] knob to edit the value.

  2. Press [F3] (EDIT) to show the SYSTEM CLICK screen.

    You can make the same settings here as with KIT CLICK.