OFF

Turns the effect off.

INTEGRA7Rev (INTEGRA 7 Reverb)

Parameter

Value

Explanation
Char ROOM1, ROOM2, HALL1, HALL2, PLATE Selects the types of reverb.
PreDelay 0–100 Adjusts the delay time from when the direct sound plays until the reverb sound is heard.
Time 0.1–10.0 [sec] Adjusts the decay length of the reverb sound.
Density 0–127 Adjusts the density of the reverb sound.
Diffusion 0–127 The greater the change over time in density of the reverb sound, the denser the reverb sounds over time. This effect is especially noticeable with long reverb times.
LF Damp 0–100 Adjusts the low-frequency portion of the reverb.
HF Damp 0–100 Adjusts the high-frequency portion of the reverb.
Spread 0–127 Adjusts the reverb spread.
Tone 0–127 Adjusts the tonal character of the reverb.
Warm Hall

Parameter

Value

Explanation

PreDelay

0.0–100.0

Adjusts the delay time from when the direct sound plays until the reverb sound is heard.

Time

0.3–30.0 [sec]

Adjusts the decay length of the reverb sound.

Pre LPF

16–15000 [Hz], BYPASS (*1)

Adjusts the frequency below which to cut the high-frequency portion of the sound fed into the reverb.

Pre HPF

16–15000 [Hz], BYPASS (*2)

Adjusts the frequency below which to cut the low-frequency portion of the sound fed into the reverb.

PreLpLPF

16–15000 [Hz], BYPASS (*1)

Adjusts the frequency above which to cut the high-frequency portion of the extended reverberation.

Diffusion

0–127

Adjusts the change in the density of the reverb over time.

HF Damp F

1000–8000 [Hz] (*3)

Adjusts the frequency above which the high-frequency portion of the reverb sound is cut.

HF Damp R

0.1–1.0

Adjusts how much to attenuate the high-frequency portion of the reverb.
Hall

Parameter

Value

 Explanation
PreDelay 0.0–100.0 Adjusts the delay time from when the direct sound plays until the reverb sound is heard.
Time 0–127 Adjusts the decay length of the reverb sound.
Size 1–8 Adjusts the size of the room/hall.
High Cut 160–12500 [Hz], BYPASS (*4) Frequency above which the high-frequency portion of the final output sound is cut (BYPASS: no cut)
Density 0–127 Adjusts the density of the reverb sound.
Diffusion 0–127 The greater the change over time in density of the reverb sound, the denser the reverb sounds over time.
This effect is especially noticeable with long reverb times.
LF Damp F 50–4000 [Hz] (*5) Adjusts the frequency below which the low-frequency portion of the reverb sound is cut.
LF Damp G -36–0 [dB] Adjusts the LF damp attenuation amount (0: no effect).
HF DampF 4000–12500 [Hz] (*6) Adjusts the frequency above which the high-frequency portion of the reverb sound is cut.
HF Damp G -36–0 [dB] Adjusts the HF damp attenuation amount (0: no effect).
GS Reverb
Parameter Value Explanation
Char ROOM1,
ROOM2,
ROOM3,
HALL1,
HALL2,
PLATE,
DELAY,
PAN-DELAY		 This selects the reverb type.
Pre LPF 0–7 Adjusts the amount of high-frequency attenuation for the sound fed into the reverb.
Time 0–127 Adjusts the decay length of the reverb sound.
Feedback 0–127 Adjusts the level at which the reverb sound is returned to the input.
SRV-2000

Parameter

Value

Explanation

Selection

R0.3, R1.0, R7.0, R15, R22, R26, R32, R37, H15, H22, H26, H32, H37, P-B, P-A

Selects the type of reverb offered by the Roland SRV-2000 digital reverb.

PreDelay

0–160

Adjusts the delay time from when the direct sound plays until the reverb sound is heard.

Time

0.1–99.0 [sec]

Adjusts the decay length of the reverb sound.

HF Damp

0.05–1.00

Adjusts the high-frequency portion of the reverb.

Density

0–9

Adjusts the density of the late reverberation.

Attack Gain

0–9

Adjusts the gain of the early reflections.

Attack Time

0–9

Adjusts the time of the early reflections.

ER Density

0–9

Adjusts the density of the early reflections.

ER Level

0–99

Adjusts the volume of the early reflections.

Low Freq

0.04–1.00 [kHz]

Sets the center frequency of the low range.

Low Gain

-24–+12 [dB]

Adjusts the boost/cut of the low frequency range.

Mid Freq

0.25–9.99 [kHz]

Sets the center frequency of the mid range.

Mid Gain

-24–+12 [dB]

Adjusts the amount of boost/cut of the mid-frequency range.

Mid Q

0.2–9.0

Sets the bandwidth of the mid-frequency range.
Higher values make the bandwidth narrower.

HighFreq

0.80–9.99 [kHz]

Sets the center frequency of the high range.

HighGain

-24–+12 [dB]

Adjusts the boost/cut of the high frequency range.

High Q

0.2–9.0

Sets the bandwidth of the high frequency range.
Higher values make the bandwidth narrower.
SRV-2000NL（NON-LINEAR）

Parameter

Value

Explanation

PreDelay

0–120

Adjusts the delay time from when the direct sound plays until the reverb sound is heard.

ReverbTime

0.9–+99.0 [sec]

Adjusts the decay length of the reverb sound.

GateTime

10–450

Adjusts the time it takes to cut off the reverb once the reverb begins to sound.

Low Freq

0.04–1.00 [kHz]

Sets the center frequency of the low range.

Low Gain

-24–+12 [dB]

Adjusts the boost/cut of the low frequency range.

Mid Freq

0.25–9.99 [kHz]

Sets the center frequency of the mid range.

Mid Gain

-24–+12 [dB]

Adjusts the amount of boost/cut of the mid-frequency range.

Mid Q

0.2–9.0

Sets the bandwidth of the mid-frequency range.

Higher values make the bandwidth narrower.

HighFreq

0.80–9.99 [kHz]

Sets the center frequency of the high range.

HighGain

-24–+12 [dB]

Adjusts the boost/cut of the high frequency range.

Hi Q

0.2–9.0

Sets the bandwidth of the high frequency range.

Higher values make the bandwidth narrower.
GM2 Reverb

Parameter

Value

Explanation

Char

SMALL ROOM,
MEDIUM ROOM,
LARGE ROOM,
MEDIUM HALL,
LARGE HALL,
PLATE

This selects the reverb type.

Time

0–127

Adjusts the decay length of the reverb sound.
Gated Reverb

Parameter

Value

Explanation

Type

NORMAL

This is a standard gate reverb.

REVERSE

This is a reverb for which the sound ramps up in volume.

SWEEP1

The reverb sound moves from right to left.

SWEEP2

The reverb sound moves from left to right.

Pre Delay

0.0–100.0 [ms]

Adjusts the delay time from when the direct sound plays until the reverb sound is heard.

Gate Time

5–500 [ms]

Adjusts the decay length of the reverb sound.
Shimmer Reverb

Parameter

Value

Explanation

Low Damp

-50–+50

Adjusts how much to attenuate the low-frequency portion of the reverb.

High Damp

-50–+50

Adjusts how much to attenuate the high-frequency portion of the reverb.

Time

0.1–10.0 [s]

Adjusts the decay length of the reverb sound.

Density

1–10

Adjusts the density of the reverb sound.

Pre Delay

0–200 [ms]

Adjusts how long it takes until the reverb sound is heard, after the direct sound plays.

Modulation Rate

0–100

Adjusts the speed at which the reverb sound is modulated.

Modulation Depth

0–100

Adjusts the depth to which the reverb sound is modulated.

Pitch1 Coarse

-24–+24 [semi]

Adjusts the amount of pitch shift applied for pitch shift 1 (in semitones).

Pitch2 Coarse

-24–+24 [semi]

Adjusts the amount of pitch shift applied for pitch shift 2 (in semitones).

Pitch1 Feedback

-98–+98 [%]

Adjusts the proportion of the delay sound that is fed back into pitch shift 1. Negative (-) settings invert the phase.

Pitch2 Feedback

-98–+98 [%]

Adjusts the proportion of the delay sound that is fed back into pitch shift 2. Negative (-) settings invert the phase.

Level 1

0–100

Adjusts the volume of pitch shift 1.

Level 2

0–100

Adjusts the volume of pitch shift 2.

(*1)

16, 20, 25, 32, 40, 50, 63, 80, 100, 125, 160, 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000, 10000, 12500, 15000 [Hz], BYPASS
(*2)

BYPASS, 16, 20, 25, 32, 40, 50, 63, 80, 100, 125, 160, 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000, 10000, 12500, 15000 [Hz]
(*3)

1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 [Hz]
(*4)

160, 200, 250, 320, 400, 500, 640, 800, 1000, 1250, 1600, 2000, 2500, 3200, 4000, 5000, 6400, 8000, 10000, 12500 [Hz], BYPASS
(*5)

50, 64, 80, 100, 125, 160, 200, 250, 320, 400, 500, 640, 800, 1000, 1250, 1600, 2000, 2500, 3200, 4000 [Hz]
(*6)

4000, 5000, 6400, 8000, 10000, 12500 [Hz]