
Parameter |
Value |
Explanation |
||
|---|---|---|---|---|
Pre Amp Sw |
OFF, ON |
Turns the amp switch on/off. |
||
ATyp |
Type of guitar amp |
|||
JC-120 |
This models the sound of the Roland JC-120. |
|||
CLEAN TWIN |
This models a Fender Twin Reverb. |
|||
MATCH DRIVE |
This models the sound input to left input on a Matchless D/C-30. |
|||
BG LEAD |
This models the lead sound of the MESA/ Boogie combo amp. |
|||
MS1959I |
This models the sound input to Input I on a Marshall 1959. |
|||
MS1959II |
This models the sound input to Input II on a Marshall 1959. |
|||
MS1959I+II |
The sound of connecting inputs I and II of the guitar amp in parallel, creating a sound with a stronger low end than I. |
|||
SLDN LEAD |
This models a Soldano SLO-100. This is the typical sound of the eighties. |
|||
METAL 5150 |
This models the lead channel of a Peavey EVH 5150. |
|||
METAL LEAD |
This is distortion sound that is ideal for performances of heavy riffs. |
|||
OD-1 |
This models the sound of the BOSS OD-1. |
|||
OD-2 TURBO |
This is the high-gain overdrive sound of the BOSS OD-2. |
|||
DISTORTION |
This gives a basic, traditional distortion sound. |
|||
FUZZ |
A fuzz sound with rich harmonic content. |
|||
| Drive | 0–127 | Volume and amount of distortion of the amp | ||
| Master | 0–127 | Volume of the entire pre-amp | ||
| Gain | LOW, MIDDLE, HIGH | Amount of pre-amp distortion | ||
| Bass | 0–127 | Tone of the bass/mid/treble frequency range | ||
| Middle | 0–127 | |||
| Treble | 0–127 | |||
| Speaker Sw | OFF, ON | Selects whether the sound will be sent through the speaker simulation (ON) or not (OFF). | ||
| STyp | Cabinet | Diameter (in inches) and number of the speaker | Microphone | |
| SMALL 1 | small open-back enclosure | 10 | dynamic | |
| SMALL 2 | small open-back enclosure | 10 | dynamic | |
| MIDDLE | open back enclosure | 12 x 1 | dynamic | |
| JC-120 | open back enclosure | 12 x 2 | dynamic | |
| BUILT-IN 1 | open back enclosure | 12 x 2 | dynamic | |
| BUILT-IN 2 | open back enclosure | 12 x 2 | condenser | |
| BUILT-IN 3 | open back enclosure | 12 x 2 | condenser | |
| BUILT-IN 4 | open back enclosure | 12 x 2 | condenser | |
| BUILT-IN 5 | open back enclosure | 12 x 2 | condenser | |
| BG STACK 1 | sealed enclosure | 12 x 2 | condenser | |
| BG STACK 2 | large sealed enclosure | 12 x 2 | condenser | |
| MS STACK 1 | large sealed enclosure | 12 x 4 | condenser | |
| MS STACK 2 | large sealed enclosure | 12 x 4 | condenser | |
| METAL STACK | large double stack | 12 x 4 | condenser | |
| 2-STACK | large double stack | 12 x 4 | condenser | |
| 3-STACK | large triple stack | 12 x 4 | condenser | |
| Phaser Sw | OFF, ON | Phaser on/off | ||
| P. Rate | 0.05–10.00 [Hz] | Frequency of modulation | ||
| Phs Manual | 0–127 | Adjusts the basic frequency from which the sound will be modulated. | ||
| Phs Depth | 0–127 | Depth of modulation | ||
| Phs Reso | 0–127 | Amount of feedback | ||
| Phs Mix | 0–127 | Level of the phase-shifted sound | ||
| Level | 0–127 | Output Level | ||