Chorus Parameters

Turns the effect off.

This is a stereo chorus.

Parameter	Value	Explanation
Rate	0–127	Adjusts the frequency of modulation.
Depth	0–127	Adjusts the depth of modulation.
Feedback	0–127	Adjusts the level of chorus sound that’s returned to the input.

This models the classic BOSS CE-1 chorus effect unit.
It provides a chorus sound with a distinctively analog warmth.

Parameter	Value	Explanation
Intensity	0–127	Adjusts the chorus depth.

This models Roland’s DIMENSION D (SDD-320).
It provides a clear chorus sound.

Parameter	Value	Explanation
Mode	1, 2, 3, 4, 1+4, 2+4, 3+4	Switches the mode.

This is a stereo delay.

Parameter	Value	Explanation
Dly Sync	OFF, ON	If this is ON, the delay synchronizes with the tempo.
Dly Msec	1–1300	Adjusts the delay time from the direct sound until the delay sound is heard.
Dly Note	Note
Feedback	-98–+98 [%]	Adjusts the proportion of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase.
HF Damp	200–8000 [Hz], BYPASS (*1)	Adjusts the frequency above which sound fed back to the effect is filtered out. If you don’t want to filter out any high frequencies, set this parameter to BYPASS.

This is a delay in which the delay time can be varied smoothly.

Parameter	Value	Explanation
Dly Sync	OFF, ON	If this is ON, the delay synchronizes with the tempo.
Dly Msec	1–1300	Adjusts the delay time from the direct sound until the delay sound is heard.
Dly Note	Note
Acceleration	0–15	When you change the delay time, this specifies the time over which the current delay time changes to the specified delay time. This affects the speed of pitch change as well as the delay time.
Feedback	-98–+98 [%]	Adjusts the proportion of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase.
HF Damp	200–8000 [Hz], BYPASS (*1)	Adjusts the frequency above which sound fed back to the effect is filtered out. If you don’t want to filter out any high frequencies, set this parameter to BYPASS.

Tremolo is applied to the delay sound.

Parameter	Value	Explanation
Input	MONAURAL	The input is mono-mixed.
Input	STEREO	The sound is input in stereo.
Dly Sync	OFF, ON	If this is ON, the delay synchronizes with the tempo.
Dly Msec	1–1300	Adjusts the delay time from the direct sound until the delay sound is heard.
Dly Note	Note
Feedback	-98–+98 [%]	Adjusts the proportion of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase.
HF Damp	200–8000 [Hz], BYPASS (*1)	Adjusts the frequency above which sound fed back to the effect is filtered out. If you don’t want to filter out any high frequencies, set this parameter to BYPASS.
Trm Switch	OFF, ON	Switches the tremolo effect on/off
Trm ModWave	This sets how the panning changes.
	TRI	Triangle wave
	SQR	Square wave
	SIN	Sine wave
	SAW1	Sawtooth wave
	SAW2	Sawtooth wave
	TRP	Trapezoidal wave
Trm Sync	OFF, ON	If this is on, the tremolo synchronizes with the tempo.
Trm Hz	0.05–10.00 [Hz]	Adjusts the rate of the tremolo.
Trm Note	Note	Adjusts the rate of the tremolo.
Trm Depth	0–127	Adjusts the depth of the tremolo.

Delay sound is heard in the two locations you specify.

Parameter	Value	Explanation
Dly Sync	OFF, ON	If this is ON, the delay synchronizes with the tempo.
Dly Msec	1–1300	Adjusts the time until the second delay sound is heard.
Dly Note	Note	Adjusts the time until the second delay sound is heard.
Feedback	-98–+98 [%]	Adjusts the proportion of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase.
HF Damp	200–8000 [Hz], BYPASS (*1)	Adjusts the frequency above which sound fed back to the effect is filtered out. If you don’t want to filter out any high frequencies, set this parameter to BYPASS.
Dly1 Pan	L64–63R	Adjusts the pan position of Delay 1.
Dly2 Pan	L64–63R	Adjusts the pan position of Delay 2.
Dly1 Level	0–127	Adjusts the volume of Delay 1.
Dly2 Level	0–127	Adjusts the volume of Delay 2.

Delay sound is heard in the three locations you specify.

Parameter	Value	Explanation
Dly Sync	OFF, ON	If this is ON, the delay synchronizes with the tempo.
Dly Msec	1–2600	Delay time of the third delay sound after the original sound is heard.
Dly Note	Note
Feedback	-98–+98 [%]	Adjusts the proportion of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase.
HF Damp	200–8000 [Hz], BYPASS (*1)	Adjusts the frequency above which sound fed back to the effect is filtered out. If you don’t want to filter out any high frequencies, set this parameter to BYPASS.
Dly1 Pan	L64–63R	Adjusts the pan position of Delay 1.
Dly2 Pan	L64–63R	Adjusts the pan position of Delay 2.
Dly3 Pan	L64–63R	Adjusts the pan position of Delay 3.
Dly1 Level	0–127	Adjusts the volume of Delay 1.
Dly2 Level	0–127	Adjusts the volume of Delay 2.

This models the chorus effects of the Roland JUNO-106.

Parameter

Value

Explanation

Mode

I, II, I+II, JX I, JX II

Type of Chorus

I+II: the state where both buttons are pressed at the same time.

Noise Level

0–127

Volume of noise

Parameter	Value	Explanation
Filter Type	OFF	The filter is not used.
	LPF	This filter cuts off the high frequencies.
	HPF	This filter cuts off the low frequencies.
Cutoff Freq	200–8000 [Hz]	Adjusts the center frequency used when the filter cuts a specific frequency region.
Pre Delay	0.0–100.0 [ms]	Adjusts the delay time from when the direct sound plays until the reverb sound is heard.
Rate Sync	OFF, ON	When this is ON, the delay synchronizes with the tempo.
Rate Hz	0.05–10.00 [Hz]	Adjusts the frequency of modulation.
Rate Note	Note	Adjusts the frequency of modulation.
Depth	0–127	Adjusts the depth of modulation.
Phase	0–180 [deg]	Adjusts the depth of the chorus sound.
Feedback	0–127	Adjusts how much of the sound that is fed into the chorus is returned to the input.

Note	1/64T, 1/64, 1/32T, 1/32, 1/16T, 1/32., 1/16, 1/8T, 1/16., 1/8, 1/4T, 1/8., 1/4, 1/2T, 1/4., 1/2, 1T, 1/2., 1, 2T, 1., 2
(*1)	200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 [Hz], BYPASS