SH-3D

Turn the [1] knob or press the [1]–[4] buttons in the OSC section to select an oscillator or LFO 2, and use the [2] knob to select the oscillator or LFO 2 waveform.
Use the [1]–[3] sliders to set the volume for each oscillator. Set the speed of the LFO 2 cycle with the [4] slider.

Parameter	Controllers	Value	Explanation
OSC 1–3
Osc 1–3 Waveform	[2] knob (on the top screen only)	This sets the waveform.
		SAW	Sawtooth wave
		SQR	Square wave
		TRI	Triangle wave
		SINE	Sine wave
		RAMP	Ramp wave
		JUNO	Modulated sawtooth wave
		TRI2	Triangle wave variation
		TRI3	Triangle wave variation
		SINE2	Sine wave variation
		SSAW	SuperSAW
		NOISE	White noise
LFO 2 Waveform	[2] knob (on the top screen only)	Sets the LFO 2 waveform.
		SINE	Sine wave
		TRI	Triangle wave
		SAW-UP	Sawtooth wave
		SAW-DW	Sawtooth wave (negative polarity)
		SQR	Square wave
		RND	Random wave
		TRP	Trapezoidal wave
		S&H	Sample & hold wave (randomly changes the output value once per cycle).
		CHS	Chaos wave
		VSINE	Deformed sine wave (randomly changes the amplitude of the sine wave once per cycle).
Osc 1–3 Coarse Tune	PITCH	-24–+24	Specifies the pitch in semitone steps (maximum ±2 octaves).
Osc 1–3 Fine Tune	SHIFT+PITCH	-50–+50	Specifies the pitch in cents (maximum ±50 cents).
Osc 1–3 PWM Depth	TIMBRE	0–63	Sets how much the LFO is applied (depth) to the PW (pulse width). The pulse width is modulated according to the LFO settings.
Osc 1–3 Pulse Width	SHIFT+TIMBRE	0–63	This effect changes the duty ratio of the pulse width to alter the waveform. You can use this effect with other waveforms besides SQR (square wave). A value of zero results in a 50:50% duty ratio.
Osc 1 Level	[OSC 1] slider	0–127	Sets the volume of OSC 1.
Osc 2 Level	[OSC 2] slider	0–127	Sets the volume of OSC 2.
Osc 3 Level	[OSC 3] slider	0–127	Sets the volume of OSC 3.
Osc 1–3 Fat	–	0–63	Distorts the waveform and adds a frequency component one octave lower than the original waveform.
Osc 1-2 Sync	–	OFF, ON	Implements the oscillator sync function that is provided by an analog synthesizer. The OSC 1 or 2 is reset at intervals of the OSC 3 or 4’s pitch cycle.
Osc 1–3 SSaw Detune	–	0–127	Adjusts how much the SuperSAW is detuned. Larger values create a greater detune effect. This is enabled only when “SSAW” is selected for the waveform.
Osc 1–3 LED Color	–	RED, ORANGE, YELLOW, GREEN, BLUE, PURPLE, PINK, WHITE, SKYBLUE, P.YELLOW, P.BLUE, P.PINK, L.RED, L.ORANGE, L.YELLOW, L.GREEN, P.GREEN, L.SKYBLUE, L.BLUE, L.PURPLE	Sets the oscillator section LED color for each oscillator.
LFO 2
LFO 2 Rate Note/Rate	[OSC 4] slider	0–1023 or 1/64T, 1/64, 1/32T, 1/32, 1/16T, 1/32., 1/16, 1/8T, 1/16., 1/8, 1/4T, 1/8., 1/4, 1/2T, 1/4., 1/2, 1T, 1/2., 1, 2T, 1., 2, 4	Sets the speed of the LFO 2 cycle. The LFO 2 cycle (rate) is set as a note length when the LFO2 Rate Sync setting is “ON”.
LFO 2 Pitch Depth	PITCH (when LFO 2 is selected)	0–100	Specifies how deeply the LFO 2 will affect pitch.
LFO 2 Fade	TIMBRE (when LFO 2 is selected)	0–1023	Sets how long it takes for LFO 2 to reach maximum amplitude.
LFO 2 Type	–	Sets the LFO 2 waveform.
		SINE	Sine wave
		TRI	Triangle wave
		SAW-UP	Sawtooth wave
		SAW-DW	Sawtooth wave (negative polarity)
		SQR	Square wave
		RND	Random wave
		TRP	Trapezoidal wave
		S&H	Sample & hold wave (randomly changes the output value once per cycle).
		CHS	Chaos wave
		VSINE	Deformed sine wave (randomly changes the amplitude of the sine wave once per cycle).
LFO 2 Rate Sync	–	OFF, ON	Turn this ON to sync the LFO 2 cycle with the tempo.
LFO 2 Key Trig	–	OFF, ON	Specifies whether the LFO 2 cycle will be synchronized to begin when the key is pressed (ON) or not (OFF).
LFO 2 Flt Depth	–	0–100	Specifies how deeply the LFO will affect the cutoff frequency.
LFO 2 Amp Depth	–	0–100	Sets how much LFO 2 affects the volume.
LFO 2 Pan Depth	–	-63–+63	Specifies how deeply the LFO will affect the pan.
LFO 2 Phase Pos	–	Sets the LFO 2 start phase value when Key Trigger is “ON”.
		0	1 cycle
		1	1/4 cycle
		2	1/2 cycle
		3	3/4 cycle